Installation ManualDishwasherFOR MODELSDWT 14210 NBL00DWT 14220 NBL00DWT 14240 NBL00DWT 15210 NBL00DWT 15220 NBL00DWT 15240 NBL00DWT 15211 NBL00DWT 15
7USA6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETSBBAA WARNINGDishwasher must be secured to adjacent cabinetry using the mounting brackets provided.
8USAAdjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height.Adjust the rear foot level with
9USA6.5 PREPARING THE WATER CONNECTION (A)Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections
10USA6.6 DRAIN PREPARATIONThe dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure A, B, C). Notice : Either on
11USAA6.7 STEAM PROTECTION FOILSteam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it
12USA7. PLACEMENT OF DISHWASHER INTO THE OPENINGNow place the dishwasher into the opening and get ready to connect all hoses and electrical connection
13USA7.1.2 PREPERATION OF WATER SUPPLY & ELECTRICAL CONNECTIONSAABBCCDDLeft side water supply connectionRight side electrical supply connectionBef
14USAFEFGGAfter installing one clip for each side push the dishwasher into the cabinet (Figure E).Note that while pushing the dishwasher into the cabi
15USA7.1.3 WATER SUPPLY CONNECTIONWater supply may be connected to the dishwasher in one of two ways:With metal braided hose.With copper tubing. C
16USAABCDInstall a strain relief (not supplied) into the opening on the kick plate. (Figure A)Pass the electrical supply cable through the strain reli
Installation Manual For Dishwasher ModelsDWT 15211 NBL00DWT 15221 NBL00DWT 15241 NBL00DWT 14210 NBL00DWT 14220 NBL00DWT 14240 NBL00DWT 15210 NBL00DWT
17USA7.3 ADJUSTING THE MOVABLE TOE KICKNow that you have successfully installed the dishwasher, you need to attach the toe kick to the dishwasher. Th
18USABstCAoAstCBopIf the enclosure height is below 331/16” (840mm) use only “o” labelled toe kick (toe kick without slots). Installation should be don
19USABC8 11/16(221,2mm)221,2mmMid. Point2. Remove the plastic mounting brackets from the dishwasher (Figure B).DD3. Lay the schematic over the door f
20USAAx4vØ 1/8" (3,5mm)B5. Attach the two mounting brackets to the wooden door with 4 screws (Ø 1/8” x 5/8” (Ø 3.5mm x 14mm) (Figure A).6. Mount
21USAyx4AØ 3/16" (4mm)Byx4CØ 3/16" (4mm)8. Using the four screws Ø 3/16” x 111/16” (Ø 4mm x 43mm) provided, attach the wooden door to the di
22USAAB0 kgC11. Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A).11.1. If the door hits the toe kick cut the necessar
23USAØ 1/8" (3,5mm)1 9/1640mmdA21 7/16(544mm)3/8 (10mm)BDCBCA Notice :If you have a European kitchen or want to install a wooden toe kick to m
24USA8. INSTALLER CHECKLISTYour installer must have completed and checked the following: The dishwasher is square and level. The dishwasher is fas
17 1844 01 00 AC-USA
Contents1. IMPORTANT SAFETY INSTRUCTIONS 11.1 INSPECT THE DISHWASHER 21.2 HOW TO CONTACT US 22. TOOLS WHICH MAY BE NEEDED 33. MATERIALS WHICH MAY
1USACAUTIONWARNINGÝNoticeINTRODUCTIONPlease read this installation manual and particularly the safety instructions completely and carefully. They will
2USAbe met to prevent injury and machine damage. Consult a qualified electrician if in doubt. Do not use any extension cord or portable outlet device
3USA2. TOOLS WHICH MAY BE NEEDED3. MATERIALS WHICH MAY BE NEEDED(Additional materials may be required to comply with local codes)Hot Water Supply Line
4USAx1x1y.x4x2x2a.b.d.e.f.g.h.c.j.k.l.m.o.p.s.v.n.r.t.x1x1x1x1x6x1x1x1x1x3x1x1x4x4x2z.x14. MATERIALS SUPPLIED4.1 PARTS SUPPLIEDParts for your dishwash
5USA5. DISHWASHER SPECIFICATIONS(861mm - 911mm)24(610mm)24(610mm)239/16(598mm)24 max(610mm max)34 - 361/4(864mm - 920mm)33 7/8- 35 7/85.1 TECHN
6USA6. ENCLOSURE PREPARATION Notice : For proper dishwasher operation and appearance ensure that the enclosure has the minimum dimensions shown in t
Kommentare zu diesen Handbüchern