Installation ManualDishwasherFOR MODELSDWT 23100 BDWT 23100 SSDWT 23100 WDWT 24100 BDWT 24100 SSDWT 24100 WDWT 24400 SS ULTRADWT 24400 W ULTRADWT 2510
7USAAdjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height.Adjust the rear foot level with
8USA6.5 PREPARING THE WATER CONNECTION (A)Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections
9USA6.6 DRAIN PREPARATIONThe dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure A, B, C). Notice :Either one of
10USAA6.7 STEAM PROTECTION FOILSteam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it
11USA7. PLACEMENT OF DISHWASHER INTO THE OPENINGNow place the dishwasher into the opening and get ready to connect all hoses and electrical connection
12USA7.1.2 PREPERATION OF WATER SUPPLYBCDALeft side water supply connectionBefore pushing the dishwasher in to the cabinet you must place water supply
13USAFEGAfter installing one clip for each side push the dishwasher into the cabinet (Figure E).Note that while pushing the dishwasher into the cabine
14USA7.1.3 WATER SUPPLY CONNECTIONWater supply may be connected to the dishwasher in one of two ways:With metal braided hose.• With copper tubing.• C
15USA7.3 ADJUSTING THE MOVABLE TOE KICKNow that you have successfully installed the dishwasher, you need to attach the toe kick to the dishwasher. The
16USABstCAoAstCBopIf the enclosure height is below 331/16” (840mm) use only “o” labelled toe kick (toe kick without slots). Installation should be don
Installation Manual For Dishwasher ModelsStart / PauseTime DelayCycle SelectHalf Load /TabletDWT 23100 BDWT 23100 SSDWT 23100 WDWT 24100 BDWT 24100 SS
17USABMax : 12,1 lb (5,5 kg)C6 1/2(155 mm)165mmMid. Point2. Remove the plastic mounting brackets from the dishwasher (Figure B).DD3. Mark the wooden
18USAAx4vØ 1/8" (3,5mm)B5. Attach the two mounting brackets to the wooden door with 4 screws (Ø 1/8” x 5/8” (Ø 3.5mm x 14mm) (Figure A).6. Mount
19USAyx4AØ 3/16" (4mm)Byx4CØ 3/16" (4mm)8. Using the four screws Ø 3/16” x 111/16” (Ø 4mm x 43mm) provided, attach the wooden door to the di
20USAAB0 kgC11. Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A).11.1. If the door hits the toe kick cut the necessar
21USAØ 1/8" (3,5mm)1 9/1640mmdA21 7/16(544mm)3/8 (10mm)BDCBCA Notice :If you have a European kitchen or want to install a wooden toe kick to m
22USA8. INSTALLER CHECKLISTYour installer must have completed and checked the following:The dishwasher is square and level.• The dishwasher is fastene
17 9077 01 00-AB-USA
Contents1. IMPORTANT SAFETY INSTRUCTIONS 11.1 INSPECT THE DISHWASHER 21.2 HOW TO CONTACT US 22. TOOLS WHICH MAY BE NEEDED 33. MATERIALS WHICH MAY
1USACAUTIONWARNINGÝNoticeINTRODUCTIONPlease read this installation manual and particularly the safety instructions completely and carefully. They will
2USADishwasher must be secured to adjacent • cabinetry using the brackets provided. Failure to do this may cause damage to property or bodily injury.C
3USA2. TOOLS WHICH MAY BE NEEDED3. MATERIALS WHICH MAY BE NEEDED(Additional materials may be required to comply with local codes)Hot Water Supply Line
4USAx1x1y.x4x2x2a.b.d.e.f.g.h.c.j.k.l.o.p.s.v.n.r.t.m.x1x1x1x1x6x1x1x1x1x1x1x4x2x2x1z.x14. MATERIALS SUPPLIED4.1 PARTS SUPPLIEDParts for your dishwash
5USA5. DISHWASHER SPECIFICATIONS(861mm - 911mm)24(610mm)24(610mm)239/16(598mm)24 max(610mm max)34 - 361/4(864mm - 920mm)33 7/8- 35 7/8max500mm5
6USA6. ENCLOSURE PREPARATION6.1 ELECTRICAL PREPARATION WARNINGThe dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a
Kommentare zu diesen Handbüchern